PVC Cut and Curl Jacketing w/ SSL (3ft)
Brand : Proto / JM
- Unit Of Measure:
- Per 3ft Long Section (35.5")
White PVC Pipe Insulation Jacket that is 20 mil PVC sheet heat curled to fit perfectly over insulated pipes. This plastic pipe wrap material is usually used in food processing facilities and mechanical rooms to create a clean look (USDA/FDA Approved).
Each piece of jacketing is 36" long and has SSL tape (Self Sealing Lap) down the inside of the lap to provide easy installation. The use of serrated tacks is allowed on hot systems (not cold/chilled). For Cold/Chilled piping systems seal laps and joints with PVC tape. For exterior applications or USDA food processing applications, please seal all laps and joints with PermaWeld PVC Liquid Adhesive or Low VOC Proto-One Adhesive for a water tight bond. Use of our Bungee Cords will help in the installation with use of the PermaWeld and Proto-One adhesives.
We can fabricate PVC Jacketing for all sizes. Give us a call for any size not listed online.
*PVC Cut & Curl Jacketing is also available in 13 high Gloss Colors!
*NOTE: PVC Cut & Curl Jacketing uses a different sizing chart than all of the other PVC Fittings. Please click on the link below to see the PVC Pipe Insulation Jacket Sizing Charts.
PVC CUT & CURL JACKETING SIZING CHARTS
Whenver I have to insulate pipes on a job I make sure to order PVC jacket too. It hides all the imperfections and literally blows the customers away when they look. I can also install a lot faster because i know the jacket will make everything okay
My local plumbing supple store was $16 or each 4 feet piece. Thank god i found this site. These are the PVC jackets you need in order to cover the fiberglass insulation of steam main pipes to give it a clean and professional look on top of sealing in the fiberglass insulation. If you have steam heating, your mains in the basement should be covered with fiberglass pipe insulation then these PVC jackets. Don't forget the elbows and unions and PVC tape. Its all here.
Great product. Arrived promptly, fit perfectly. covered unsightly fraying insulation with a sleek, white finish.
This is made of quality durable material. Can cut to length with sturdy scissors or snips. The peel and stick edge seems to have good adhesion.
We used this to cover some insulated pipes in our church basement hall that went from the floor to the ceiling. The previous insulation had been ripped to shreds from people bumping into it, furniture getting moved against it, etc. It did not look good and was not great to have kids around it.
We put on new insulation and then put this PVC jacketing over the top to protect it. It definitely looks a lot better than the old ripped insulation and even looks better than the brand new insulation (which we also purchased from this store). So the looks are definitely good.
It remains to be seen how long this will last. Note that this is fairly thin PVC, which is good for installation since it is fairly flexible and easy to mold around the pipe insulation. But I'm not sure how it is going to hold up when furniture gets shoved against it. And it is white, so I'm not sure how dirty it will get. It is glossy, though, so it shouldn't be hard to clean. But even if the PVC gets damaged, this is cheap and easy enough to install that I'm sure we could put another layer on if we wanted to.
It's slightly annoying that these come in 4' lengths while the insulation comes in 3' lengths. Maybe this is standard in the industry, but it means you have to do some fancy math to make sure you're getting the right amount for your project, and you're pretty much guaranteed to have to do some cutting.
The sizing is perfect when matched with the pipe insulation. As I mentioned this is flexible, so you might be able to get away with slight differences in sizes, too, if that was needed. The adhesive strip is easy to use.
Overall a quality product at a reasonable cost. Thanks!
*Aaron, thank you for the great review. We have now changed the length of this product from 4ft down to 3ft for ease of calculation. ~ BIP