Loading... Please wait...
  • Gift Certificates
  • My Account 

CALL US: 888-367-8931        E-MAIL US: CLICK HERE 

INSTALL A PVC UNION COVER

INSTALL A PVC UNION COVER

If you are reading this short blog post, you already understand the importance of pipe insulation.  We get many customers who send us thank you emails and photos of their finished insulation projects.  One common occurrence is that many of these photos show pipe insulation and PVC fitting covers everywhere and then a single pipe union or valve with no insulation.  This post will help explain the ways to fix these issues regarding that single or sometimes multiple Pipe Union connectors: 

Pipe Union Connection

A pipe union (shown above) is used to connect piping with the use of a large nut that threads over the pipe connection.  This large nut is a problem when using 1/2" or 1" thick pipe insulation due to the outside diameter (OD) of the nut being as wide or wider than the OD of the pipe insulation.  We find that many times pipe insulation is only installed up the the pipe union only which leaves the union uninsulated. This is obviously not an efficient insulation system.

 

CARVE OUT METHOD:

When using thicker pipe insulation (1-1/2" or 2" thick), the installer can simply carve out some of the insulation on the inside of the pipe insulation to accommodate the raised union nut.  

First you must determine if the OD of your pipe insulation is greater than OD of the union nut.  You want to have around a 2" greater OD than the union nut this way you will still have 1" of insulation around the nut on all sides.  Find out where the pipe union will fall on your piece of fiberglass pipe insulation.  Open up the pipe insulation so you have two C's (halves of pipe insulation) hinged before you.  Make two cuts into the insulation on both of the C's.  These cuts should represent the width of the union.  Pinch the fiberglass and peel out a layer of fiberglass (similar to peeling off a layer of onion).  Simply pop the piece of pipe insulation onto the pipe with the carve out falling onto the union nut.

PVC UNION COVER:

A PVC Union Cover (shown below) is used to easily insulate over a pipe union while leaving a clean look to the finished pipe insulation system.  The PVC Union Covers are low profile which mean they are sized accurately to only raise above the OD of the pipe insulation as little as necessary.  The PVC Union Covers will cover up to an approximate 1" raise off of the piping (2" OD larger than the pipe insulation OD).  These covers come with a rectangle fiberglass insert which is first wrapped around the union itself and the PVC cover is installed over the fiberglass.  The PVC Union cover is a 2 piece fitting which means that it comes in two halves.  The two halves are installed with either King Tacks (on hot system) or PVC Vinyl tape (cold systems).

PVC Union Cover for Insulating over Pipe Union Connections

How to Install Our PVC Union Cover

Exposed Pipe Union Left Uninsulated

The image above shows how many pipe unions are left exposed even after pipe insulation is installed.  The exposed pipe fitting will radiate heat loss and negatively affect the efficiency of the pipe insulation system.

Wrapping Pipe Union with Fiberglass Wrap

Our PVC Union Cover comes with a fiberglass insert wrap that is used to fully insulate the pipe union.  Simply wrap the fiberglass around the union making sure all parts are sufficiently covered by fiberglass.

Pipe Union Completely Insulated with Fiberglass Wrap

Finished wrapping the fiberglass insert around the union.  As you can see there should be no gaps between the fiberglass insert and the adjacent pipe insulation.

PVC Union Cover Installed over Fiberglass Wrap

Half of the PVC Union Cover is placed over the fiberglass wrap.  Each PVC Union Cover is sized to perfectly sit on top of the outside of the fiberglass pipe insulation.

PVC Union Cover Installed

Both halves of the PVC Union Cover are installed.  On hot systems, King Tacks should be used to connect the two halves of the cover.  The serrated tack is pushed into the 4 spots where the two halves overlap.  On cold systems, use of PVC Vinyl tape should be used for proper closure.

 
bip-large.png

Recent Blog Posts

newsletter

Copyright 2017 Buy Insulation Products. All Rights Reserved.
Sitemap |